In-furrow starter fertilizers for wheat

Share Tweet Email


Wheat is considered a highly responsive crop to starter fertilizers, particularly phosphorus (P) and nitrogen (N). Application of P as starter fertilizer can be an effective method for part or all the P needs. Wheat plants typically show a significant increase in fall tillers (Figure 1) and better root development with the use of starter fertilizer (P and N). Winterkill can also be reduced with the use of starter fertilizers, particularly in low P testing soils.


Figure 1. Effects on wheat tillering and early growth with in-furrow P fertilizer on soil testing low in P. Photo taken in 2019 in Manhattan, KS. Photo by Chris Weber, K-State Research and Extension.


Starter fertilizer application

Phosphorus fertilizer application can be done through the drill with the seed. Starter fertilizer can be applied, depending on the soil test and recommended application rate, either in addition to or instead of, any pre-plant P applications. The use of dry fertilizer sources with air seeders is a very popular and practical option. However, other P sources (including liquid) are agronomically equivalent and decisions should be based on cost and adaptability for each operation.

When applying fertilizer with the seed, rates should be limited to avoid potential toxicity to the seedling. When placing starter fertilizer in direct contact with wheat seed, producers should use the guidelines in Table 1.

 

Table 1. Suggested maximum rates of fertilizer to apply directly with the wheat seed

 

Pounds N + K2O (No urea containing fertilizers)

Row spacing
(inches)

Medium-to-fine
soil textures

Course textures or dry soils
 

15

16

11

10

24

17

6-8

30

21

 


Air seeders that place the starter fertilizer and seed in a 1- to 2-inch band, rather than a narrow seed slot, provide some margin of safety because the concentration of the fertilizer and seed is lower in these diffuse bands. In this scenario, adding a little extra N fertilizer to the starter is less likely to injure the seed - but it is still a risk.

What about blending dry 18-46-0 (DAP) or 11-52-0 (MAP) directly with the seed in the hopper? Will the N in these products hurt the seed?

The N in these fertilizer products is in the ammonium-N form (NH4+), not the urea-N form, and is much less likely to injure the wheat seed, even though it is in direct seed contact. As for rates, guidelines provided in the table above should be used. If DAP or MAP is mixed with the seed, the mixture can safely be left in the seed hopper overnight without injuring the seed or gumming up the works.  However, it is important to keep the wheat mixed with MAP or DAP in a lower relative humidity.  A humidity greater than 70% will result in the fertilizer taking up moisture and will cause gumming or caking within the mixture.  

How long can you allow this mixture of seed and fertilizer to set together without seeing any negative effects to crop establishment and yield?

The effects of leaving DAP fertilizer left mixed with wheat seed for various amounts of time is shown in Figure 2. Little to no negative effect was observed (up to 12 days in the K-State study) as long as the mixture is stored at a relative humidity less than 70%.


Figure 2. Effects on wheat yield from mixing P fertilizer with the seed. Study conducted in 2018-2019 at sites in Manhattan and Topeka. Graph by Chris Weber, K-State Research and Extension.


Although the wheat response to these starter fertilizer products is primarily from the P, the small amount of N that is present in DAP, MAP, or 10-34-0 may also be important in some cases. If no pre-plant N was applied, and the soil has little or no carryover N from the previous crop, the N from these fertilizer products could benefit the wheat.

Dual-placement of N and P (anhydrous ammonia or UAN plus 10-34-0 applied in the same band below the soil surface) is a fertilizer application method usually used in pre-plant applications. Ammonium-N has long been known to increase P uptake by crops, and dual-placement can be very effective. Sometimes, producers will use this method at planting time, trying to position the band to the side of each row of wheat seed. Be advised to use caution. If adequate separation of fertilizer and seed is accomplished, this is a good application method that fits into many farmers’ overall no-till system. If adequate separation of the ammonia/UAN and seed is not accomplished, wheat germination/stand establishment can be affected.

 

 

Dorivar Ruiz Diaz, Nutrient Management Specialist
ruizdiaz@ksu.edu

Chris Weber, Graduate Research Assistant, Soil Fertility
cmweber@ksu.edu


Tags:  wheat fertilizer 

Search
Events
Subscribe