The 2024 wheat harvest is well underway, so it is time to think about weed control in wheat stubble. Weeds that have been suppressed by the canopy will grow rapidly once crop competition is removed. In addition, weeds that have emerged through the wheat canopy will be damaged during harvest and will quickly begin regrowth. Delaying control can result in lost soil moisture that could be used for crop production, as well as weed seed production which will cause difficulties in the future.
When thinking about weed control in wheat stubble, there are two priorities – controlling already emerged weeds and preventing later flushes. Making applications before weeds exceed 4 to 6 inches is necessary for good control of already emerged weeds (Figure 1). Residual herbicides are needed to reduce the number of herbicide applications needed to control multiple flushes of weeds.
Figure 1. This large Palmer amaranth is regrowing after being sprayed with paraquat. Photo by Sarah Lancaster, K-State Research and Extension.
Despite a growing number of herbicide-resistant weeds, glyphosate plus 2,4-D LVE and/or dicamba remain important for weed control in wheat stubble. However, these herbicides alone are not likely to provide adequate control of pigweeds or kochia, especially when applied in the hot, dry conditions that are common after wheat harvest. Strategies for more successful herbicide applications in high temperatures were discussed in the article published last week. The following paragraphs list some herbicide options commonly used to control weeds after wheat harvest.
Paraquat (Gramoxone, others) is a Group 22 herbicide that can work well in place of glyphosate to control emerged pigweed and kochia. Paraquat is a contact herbicide, so spray coverage is critical. Spray volumes of 20 gallons/acre or higher are preferred, especially on larger weeds or denser stands. If sprayed at less than 20 GPA, flat fan nozzles are required. Paraquat needs to be applied with a non-ionic surfactant or oil concentrate to enhance the surface coverage of the plant foliage. Also, remember that there is a requirement for handlers and applicators to complete training every three years to use paraquat.
If planning to plant corn or sorghum next spring, a tank mix of paraquat with atrazine (Group 5) will enhance the control of emerged weeds and provide some residual weed control. Atrazine labels have recently changed so that the only noncrop uses of atrazine permitted are in wheat-fallow-wheat, wheat-corn-fallow, and wheat-sorghum-fallow rotations. In these rotations, it is still important to be aware of the total amount of atrazine you are applying to each field in a given year and stay below the maximum rate allowed for your field. Metribuzin is another Group 5 herbicide that can be used instead of atrazine to enhance control and provide some residual activity. There are two benefits of using metribuzin instead of atrazine. First, there are more options for crop rotation. Atrazine limits crop options to corn or sorghum in the next season, whereas metribuzin can be applied as a preemergence herbicide for soybeans or field peas. Second, metribuzin is likely unaffected by enhanced degradation associated with extensive atrazine use.
One final note regarding paraquat. Limited research out of Australia suggests applying paraquat 2 weeks after a glyphosate application will increase weed control. This is called a ‘double knock’ strategy. This information is included here not as a recommendation per se but to encourage careful thought about when you want to utilize contact herbicides in your fallow weed management system. If paraquat were sprayed with or before glyphosate, the rapid damage to leaf tissue will prevent uptake and translocation of glyphosate. However, if a glyphosate application partially controls weeds, there will be sufficient leaf area 2 weeks after application for paraquat to be effective.
Saflufenacil (Sharpen) is a Group 14 herbicide applied at one to two fluid ounces per acre is an option to provide postemergence and short-term residual control of Palmer amaranth, kochia, and other broadleaf weeds. Sharpen should be applied with glyphosate for grass control, and can be applied with other products labeled for use in wheat stubble, but do not apply Sharpen with Valor. Sharpen works best with the addition of methylated seed oil and ammonium sulfate. Good spray coverage is needed, so using 15 to 20 gallons/acre spray solution is important. Be sure to note crop rotation intervals for your situation, especially if using more than one fluid ounce per acre or applying to sandy or low organic matter soils. Tiafenacil (Reviton) is a Group 14 that is very similar to Sharpen in terms of weed control and adjuvant use.
Flumioxazin (Valor, others) is a Group 14 herbicide that can be added to burndown treatments at rates of one to four fluid ounces per acre for activity on emerged broadleaf weeds and some residual activity on broadleaf and grass weeds in wheat stubble. Flumioxazin can be mixed with glyphosate or clethodim (Select Max) for enhanced grass control. It can also be mixed with 2,4-D, atrazine, metribuzin, or paraquat. Wheat can be planted 30 days after two fluid ounces per acre or 60 days after three fluid ounces per acre if at least one inch of rain occurs between application and planting. Soybeans can be planted immediately after applying three fluid ounces per acre. Corn, sorghum, cotton, sunflowers, or soybeans can be planted in the spring after applying four fluid ounces per acre. Residual weed control with flumioxazin will depend on rainfall (0.25 inch) for activation, just as with pre-plant treatment in soybeans. Of the three Group 14 herbicides discussed, flumioxazin is the only herbicide with meaningful residual activity; however, saflufenacil provides greater kochia control than flumioxazin.
For more detailed information, see the “2024 Chemical Weed Control for Field Crops, Pastures, and Noncropland” guide available online at https://www.bookstore.ksre.ksu.edu/pubs/CHEMWEEDGUIDE.pdf or check with your local K-State Research and Extension office for a paper copy.
The use of trade names is for clarity to readers and does not imply endorsement of a particular product, nor does exclusion imply non-approval. Always consult the herbicide label for the most current use requirements. Users should read and follow all label directions.
Sarah Lancaster, Weed Science Extension Specialist
slancaster@ksu.edu
Jeanne Falk Jones, Multi-County Agronomist
jfalkjones@ksu.edu
Jeremie Kouame, Weed Scientist – Agricultural Research Center, Hays
jkouame@ksu.edu
Tags: wheat weeds weed control wheat harvest