Calibrating the seed drill prior to wheat planting to improve seed distribution

Share Tweet Email

Decisions taken prior to wheat planting can account for a large proportion of the success or failure of the wheat crop. These decisions include:

  • selecting a variety well adapted to the area and with a good yield stability record
  • soil sampling to determine fertility needs
  • pre-plant fertilization (N, P, K, lime)
  • tillage for weed control and seedbed preparation (or using a contact herbicide in no-till situations)
  • proper drill calibration
     

Proper drill calibration can increase the chances of success of the wheat crop by ensuring the amount of seed planted per acre is close to the target.   

There are several methods to calibrate seed drills. The stationary method, which is a simple 5-step method to calibrate a wheat drill prior to planting, is discussed in this article. In stationary drill calibration, a drill operation is simulated by turning the drive wheel freely above ground, weighing the seeds delivered from the drill spouts, and comparing to a targeted seed weight by length of drill-row.

 

The five steps are as follows:
 

1.  Determine seeding density.

Targeted seeding density varies within the State of Kansas based on annual precipitation. A target range of seeds per acre based on current K-State recommendations is shown in Table 1.
 

Table 1.  Target seeding density based on annual precipitation

 

Target seeding density

(seeds per acre)

Annual precipitation

> 20 in

675,000 - 900,000

20 - 30 in

900,000 - 1,125,000

>30 in

1,125,000 - 1,350,000

Irrigated

1,350,000 - 1,800,000

 

2.  Determine the number of seeds to be placed in 50 drill-row feet based on row spacing and targeted seeding density.

Determine the number of linear row feet per acre based on the drill’s row width (Table 2). Next, estimate the number of seeds to be collected in 50 drill-row feet based on row width and the target seeds per acre. This can be done by dividing the number of target seeds per acre by the number of linear row feet per acre based on row width and multiplying the result by 50. Percent emergence can be accounted for by dividing the result by the fraction of emergence (for example, dividing by 0.85 for 85% emergence). Table 2 shows calculations for selected row widths and targeted number of seeds per acre considering 85% emergence.

After determining the number of seeds to be collected from 50 drill-row feet, weigh the equivalent amount of seed of each variety you intend to plant. For instance, if the target is 675,000 seeds per acre and row width is 12 inches, a total of 775 seeds need to be planted in a 50 drill-row feet. Assuming 85% emergence, this number increases to 912 seeds (Table 2). Count and weigh 912 seeds from each variety. If no scale is available, place the 912 seeds in a clear graduated cylinder (i.e. a rain gauge) and mark the level for each variety.
 

Table 2. Seeds per 50 drill-row feet as function of row width and target number of seeds per acre. Feet of linear row per acre as a function of row width is also shown.

 

Row width

(inches)

 

Feet of linear row per acre

 

Target number of seeds per acre

675,000

750,000

900,000

1,125,000

1,350,000

1,800,000

Seeds per 50 drill-row feet

6

87,120

456

506

608

760

912

1,215

7

74,674

532

591

709

886

1,063

1,418

7.5

69,696

570

633

760

950

1,139

1,519

8

65,340

608

675

810

1,013

1,215

1,620

10

52,272

760

844

1,013

1,266

1,519

2,026

12

43,560

912

1,013

1,215

1,519

1,823

2,431

 

3.  Determine the number of wheel revolutions needed for 50 drill-row ft.

First, attach the seed drill to a tractor and raise the drill off the ground. Measure the drive wheel’s circumference using a tape measure, and divide 50 drill-row feet by the length of the circumference to determine how many times the drive wheel needs to be rotated to account for 50 drill-row feet. For example, if the drive wheel’s circumference is 7 feet, dividing 50 by 7 indicates that the wheel needs to be rotated 7.15 times to account for 50 drill-row feet. Mark a starting point in the wheel with tape (i.e. duct tape) to facilitate counting how many times the wheel is being turned.
 

4.  Calibrate the drill.

Adjust the seed meter using the rate chart provided by the manufacturer for the desired seeding rate, which should result in a first approximation of final calibration. Add enough seed of the variety to be calibrated to ensure seed cups will remain covered throughout the calibration process. Rotate the wheel the number of revolutions needed to cover 50 drill-row feet as calculated in step 3 and collect the seed from each spout in a bucket or similar container. The more spouts evaluated, the more accurate the calibration. Weigh the collected seed (or pour it in the marked graduated cylinder from step 2) and compare to the target seed per 50 drill-row feet as determined in step 2. If the collected seed weighs too low or too heavy compared to the target, adjust the metering system to deliver more or less seeds, respectively. It is recommended to keep a record of the different seeding rates achieved at each setting for future reference. Repeat this process until the number of seeds delivered from the drill spouts matches the target established in step 2.


 

Romulo Lollato, Wheat and Forages Specialist
lollato@ksu.edu


Tags: 

Tags
Search
Subscribe